IndraLogic XLC / IndraMotion MLC 13VRS fault codes & diagnostics

ML_SendJobTlg, Invalid state of state machine of POU

ML_SendJobTlg, Error during init of POU instance

ML_RecvJobTlg, Invalid values of inputs of POU

ML_RecvJobTlg, Set of command into queue failed

ML_RecvJobTlg, Watch dog - time out

ML_RecvJobTlg, Invalid state of state machine of POU

ML_RecvJobTlg, Error during init of POU instance

ML_SendRecvJobAss, Invalid values of inputs of POU

ML_SendRecvJobAss, Store of recieved job telegram failed

ML_SendRecvJobAss, Watch dog - time out

ML_SendRecvJobAss, Error communication socket (create)

ML_SendRecvJobAss, Error communication socket (close)

ML_SendRecvJobAss, Error communication socket (ioctl)

ML_SendRecvJobAss, Error communication socket (bind)

ML_SendRecvJobAss, Error ethernet buffer (recvfrom)

ML_SendRecvJobAss, Error ethernet buffer (sendto)

ML_SendRecvJobAss, Defrag error of send/ receive buffer

ML_SendRecvJobAss, Error on communication sockets

ML_SendRecvJobAss, Invalid state of I/O of POU

ML_SendRecvJobAss, Invalid state of state machine of POU

ML_SendRecvJobAss, Error during init of POU instance

ML_DebugJobConnect, Invalid values of inputs of POU

ML_DebugJobConnect, Set of command into queue failed

ML_DebugJobConnect, Invalid command / getting status

ML_DebugJobConnect, Invalid command / getting status

ML_DebugJobConnect, Watch dog - time out

ML_DebugJobConnect, Invalid state of state machine of POU

ML_DebugJobConnect, Error during init of POU instance

Invalid number of CFL01.1 modules (-Q2, -R3)

Upload of firmware into des CFL01.1-Q2-FPGA failed

Initialization of the CFL01.1-Q2 module failed

Link ring broken

Link ring: masterposition incorrect MDT

Link ring: masterposition incorrect AT

Link ring: variant cycle time detected

Link axis not projectable, C2C is not configured yet

C2C: Connection not applicable, as not configured

C2C: Connection error

Semaphore error while switching C2C phase

Invalid commanded C2C phase

Internal error due to the C2C service channel

Incompatible C2C device found

C2C ring not closed

C2C: Configuration not consistent

C2C: Error device not found

C2C: Error switching phase 3

C2C: Error command S-0-0127, P3 transition check

C2C: Error switching phase 4

Invalid configuration of C2C timing

C2C: sercos cycle time not possible

Link ring: invalid HW synchronization

C2C master: hot plug slave w/o sercos III-interface (HP0)

C2C master: misconfigured hot plug slave (HP0)

C2C master: error while scanning the hot plug slaves (HP1)

C2C master: HP1 parameters faultily receipted (HP1)

C2C master: error running the service channel (HP1)

C2C master: hot plug mechanism aborted

C2C master: HotPlug not supported

C2C master: invalid slave address detected (HP1)

Ring topology could not be established

C2C slave: hot plug via C2C master impossible (HP0.1)

C2C slave: HP0 parameters defective/incomplete (HP0.2)

C2C slave: slave address missed in HP control word (HP0.3)

C2C slave: HP1 parameters defective/incomplete (HP01.1)

C2C slave: error within C2C service channel (HP1.2)

C2C slave: faulty scan algorithm within C2C master (HP1.2)

C2C slave: error running switch command S-0-0127/8 (HP2)

C2C slave: hot plug mechanism failed

Lack of memory due to the C2C interface data

Initialization of the C2C hardware failed

Master axis not applicable, defective internal axis table

Old master axis unerasable, defective internal axis table

Setup of the P-/S-Count values via SVCH failed

Enquiry of the P-/S-SynCnt values via SVCH failed

Enquiry of the ring configuration ID via SVCH failed

Generic (configuration) error due to the C2C interface

Set point transfer error

Transformation not valid

General kinematics error

Invalid control number