IndraDrive · MPx-02 to MPx-08
IndraDrive MPx-02 to MPx-08 / HMV fault codes & diagnostics
IndraDrive MPx-02 to MPx-08 / HMV diagnostic index: source-listed messages and printed manual references. Match this firmware to your equipment before using a code.
Check the source and revision
DOK-INDRV*-GEN-**VRS**-WA08-EN-P
21-page diagnostic index excerpt · MPx-02 to MPx-08
These are the manufacturer’s index descriptions, not complete causes or repair instructions. “Source PDF page” opens the supplied index; “printed manual reference” identifies the destination in the full manual, which may not be included here.
Find a display message
Keep every letter, number and indicator. These entries describe the source document, not the condition of a particular machine.
Showing 321–400 of 762 source entries
E4011
WarningCommunication watchdog: Overload of cyclic communication
Source PDF · page 10 ↗Printed manual reference: 299E4012
WarningE4013
WarningE4014
WarningE4016
WarningE4017
WarningE3100
WarningE3101
WarningE3102
WarningE3103
WarningE3104
WarningE3105
WarningE3106
WarningE3107
WarningE3108
WarningE3110
WarningE3115
WarningE3116
WarningE2010
WarningE2011
WarningE2012
WarningE2013
WarningE2014
WarningE2015
WarningE2016
WarningE2017
WarningE2021
WarningE2026
WarningE2040
WarningE2047
WarningE2048
WarningE2049
WarningE2050
WarningE2051
WarningE2053
WarningE2054
WarningE2055
WarningE2056
WarningE2058
WarningSelected positioning block has not been programmed
Source PDF · page 11 ↗Printed manual reference: 323E2059
WarningE2061
WarningE2063
WarningE2064
WarningE2069
WarningE2070
WarningE2074
WarningE2075
WarningE2076
WarningE2077
WarningAbsolute encoder monitoring, motor encoder (encoder alarm)
Source PDF · page 11 ↗Printed manual reference: 330E2078
WarningAbsolute encoder monitoring, opt. encoder (encoder alarm)
Source PDF · page 11 ↗Printed manual reference: 331E2079
WarningAbsolute enc. monitoring, measuring encoder (encoder alarm)
Source PDF · page 11 ↗Printed manual reference: 331E2086
WarningE2092
WarningE2100
WarningPositioning velocity of master axis generator too high
Source PDF · page 11 ↗Printed manual reference: 333E2101
WarningE2140
WarningE2270
WarningE2802
WarningE2810
WarningE2814
WarningE2816
WarningE2818
WarningE2819
WarningE2820
WarningE2829
WarningC0100
Command / diagnosticC0200
Command / diagnosticC0300
Command / diagnosticC0400
Command / diagnosticActivate parameterization level 1 procedure command
Source PDF · page 12 ↗Printed manual reference: 342C0500
Command / diagnosticC0600
Command / diagnosticC0700
Command / diagnosticLoad defaults proced. command (motor-spec. controller val.)
Source PDF · page 12 ↗Printed manual reference: 343C0720
Command / diagnosticLoad defaults procedure command (safety technology)
Source PDF · page 12 ↗Printed manual reference: 344C0730
Command / diagnosticC0740
Command / diagnosticC0750
Command / diagnosticLoad defaults procedure command (factory settings)
Source PDF · page 12 ↗Printed manual reference: 346